s i da40 series 40w desktop power supply for industrial equipment C wide input voltage 90 to 264 vac, 47 to 63hz C iec - 320 - c14 input inlet C output voltage available from 5vdc thru 50vdc C approved as limited power source (lps), splash proof C class i insulation C operating temperature - 20~70c C input surge current, over voltage, over load and output voltage protection. C energy star, cec v/iv,and rohs compliance 3 year warranty approvals: single output part number output voltage max. output current total regulation max. output power s i da40 - s02 * 5 ~ 6 vdc 4.16 ~ 5.00 a 5% 25w s i da40 - s03 * 6 ~ 8 vdc 5.00 ~ 3.75 a 5% 30w s i da40 - s04 8 ~ 11 vdc 3.63 ~ 5.00 a 4% 35w s i da40 - s05 11 ~ 13 vdc 3.07 ~ 3.63 a 3% 40w s i da40 - s06 * 13 ~ 16 vdc 3.07 ~ 2.50 a 3% 40w s i da40 - s07 * 16 ~ 21 vdc 1.90 ~ 2.50 a 3% 40w s i da40 - s08 * 21 ~ 27 vdc 1.48 ~ 1.90 a 2% 40w s i da40 - s09 27 ~ 33 vdc 1.48 ~ 1.21 a 2% 40w s i da40 - s10 33 ~ 40 vdc 1.21 ~ 1.00 a 2% 40w s i da40 - s11 40 ~ 50 vdc 1.00 ~ 0.80 a 2% 40w mark " * " means " pse approval " the model number of s05~s11 had been approved by cec level v. model. s02~s05 shall use awg#16,4ft long to meet the requirement of cec. model. s06~s11 shall use awg#18,4ft long to meet the requirement of cec. the regulation will be changed by modified output cable. electrical characteristics parameter test conditions min. typ. max. unit input voltage operating voltage 90 264 vac input frequency 47 63 hz output power range vin=90 to 264vac 0 40 w input current (low line) io=full load, vin=115vac 1 a input current (high line) io=full load, vin=230vac 0.5 a low line inrush current io=full load, 25c, cool start, vin=100vac 20 25 a high line inrush current io=full load, 25c, cool start, vin=230vac 42 50 a efficiency io=full load, vin=230vac 78 83 90 % line regulation io=full load 0.5 1 % load regulation vin=230vac 3 7 % over voltage protection 112 132 % over current protection 110 150 % transient response io=full load to half load,vin=100vac 4 ms hold - up time io=full load, vin=110vac 12 ms start up time io=full load, vin=100vac 0.3 0.5 s ripple & noise (peak to peak) full load, vin=90vac 0.5 1 % safety ground leakage current io=full load, vin=240vac 0.5 0.75 ma temperature coefficient all output - 0.04 0.04 %/c no - load power consumption no load, vin=240vac 0.3 0.5 w
conditions parameter test conditions min. typ. max. unit operating temperature - 20 40 70 c storage temperature - 40 85 c relative humidity 5 95 % operation temperature at 25c, calculated per mil - hdbk - 217f 0.1 m hrs der ate linearly from 100% load at 4 0c to 50% load at 70c approvals and compliances parameter test conditions min. unit dielectric withstanding voltage for primary to secondary primary to secondary 4242 vdc dielectric withstanding voltage for primary to ground primary to ground 2121 vdc isolation resistance test voltage = 5 00vdc 50 m emi requirements for cispr - 22 vin=220vac b class emi requirements for fcc part - 1 5 vin=110vac b class mechanical and pin out note: 1. dimensions are shown in mm & inch 2. weight: approx. 275g (exclude the input cord) 3. optional output connector.
|
